-
Finished your HSC? Check out our University Discussion, Non-School forums or help out next year's HSC students! -
YOU can help the next generation of students in the community! Share your trial papers and notes on our Notes & Resources page
Gaps in knowledge? Fill them in here! (1 Viewer)
- Thread starter PimpPyro
- Start date
fakingtheday
Member
Digital Control Technology
In a nutshell a computer monitors, senses changes and then uses technology to rectify problems. I use ABS where a computer monitors the braking stress on each wheel, and if it senses a wheel locking from the braking it redistributes this force to other wheels.
Benefits include increased safety of cars, braking efficiency and in turn a greater fuel efficiency.
In a nutshell a computer monitors, senses changes and then uses technology to rectify problems. I use ABS where a computer monitors the braking stress on each wheel, and if it senses a wheel locking from the braking it redistributes this force to other wheels.
Benefits include increased safety of cars, braking efficiency and in turn a greater fuel efficiency.
fakingtheday
Member
Just incase i'd also have this one up your sleeve. Regnerative Braking is widely used in Europe now. WHere powere used by trains when braking is sent back up into the grid and to power other trains on the grid. Just from memory. Just remember:
Senser -> Controller -> Resdistribution (or whatever)
Senser -> Controller -> Resdistribution (or whatever)
fakingtheday
Member
*doesn't do physics*
dodgeviper
New Member
- Joined
- Feb 7, 2005
- Messages
- 6
- Gender
- Male
- HSC
- 2005
conrol devices are easy, pretty much anythign digital cruise control etc, as it has one choice or another
some knowledge that i need filling in specific detail is grain structures for
-all heat treatment
-all castings
and quick question to you guys, how much detail are you memorising on cast adn wrought irons, as well as brazz and bronze alloys. as there is is stacks of info on it but it seems trival.
also im confused with tv synchronisation if anyone can help me with that.
thnx gl studying
some knowledge that i need filling in specific detail is grain structures for
-all heat treatment
-all castings
and quick question to you guys, how much detail are you memorising on cast adn wrought irons, as well as brazz and bronze alloys. as there is is stacks of info on it but it seems trival.
also im confused with tv synchronisation if anyone can help me with that.
thnx gl studying
Mat_Aussie
Member
Here are some notes on heat treatment that i found
so its not mine, but i hope it helps
Mat
so its not mine, but i hope it helps
Mat
fakingtheday
Member
Annealing - large equiaxed grains, soft ductile
Normalising - refined grains, tougher
Hardened - asicular grains. Matrensite. very hard and brittle
Tempered - no inner stresses, hard and tough
Surface hardened; carburising: higher carbon content on the skin makes it harder
flame induction and quenching gives martensite skin. harder
Normalising - refined grains, tougher
Hardened - asicular grains. Matrensite. very hard and brittle
Tempered - no inner stresses, hard and tough
Surface hardened; carburising: higher carbon content on the skin makes it harder
flame induction and quenching gives martensite skin. harder
fakingtheday
Member
you have to use m for everything in engineering!
a MPa is 1 x 10^6 and a Gpa is 1 x 10^9
a MPa is 1 x 10^6 and a Gpa is 1 x 10^9
fakingtheday
Member
xrtzx: i got 187N as the force, it's just the addition of the FF which is equal to 0.3 x (cos10 x300) and component down the plane which is sin10 x 300.
i use rochford when i need it but my teacher is the best resource going dude.
i use rochford when i need it but my teacher is the best resource going dude.
dodgeviper
New Member
- Joined
- Feb 7, 2005
- Messages
- 6
- Gender
- Male
- HSC
- 2005
where did u get rockford?
Q12 (b)
What did everyone get for the 2004 HSC Q12 (b) for the reaction at support 1 and the force in member A
I got 2740N for the reaction at support 1 but I don't know how to get the force in member A
Can someone Please help me!!
What did everyone get for the 2004 HSC Q12 (b) for the reaction at support 1 and the force in member A
I got 2740N for the reaction at support 1 but I don't know how to get the force in member A
Can someone Please help me!!
fakingtheday
Member
that's the right answer
thanks for the help but now I have another Question to ask for the Q14 (a) 2004 HSC again
Here is the question:
Question 14 — Lifting Devices (10 marks)
(a) A crane uses a DC electric motor to lift a mass of 250 kg vertically from the
ground. After 18 seconds the mass is 20 metres off the ground with an upward
velocity of 2 ms−1.
(i) Determine the average power required by the motor to perform this
lifting operation.
Power = ................................ kW
I dont know how to calculate the work, I think it is 250kg x 10ms x 20m= 50000Nm
If I know what the work is then I can put it into the formula Power = Work / Time
Which by me would equal 50000/ 18 = 2777.8
Could someone please tell me what the actual answer is
Here is the question:
Question 14 — Lifting Devices (10 marks)
(a) A crane uses a DC electric motor to lift a mass of 250 kg vertically from the
ground. After 18 seconds the mass is 20 metres off the ground with an upward
velocity of 2 ms−1.
(i) Determine the average power required by the motor to perform this
lifting operation.
Power = ................................ kW
I dont know how to calculate the work, I think it is 250kg x 10ms x 20m= 50000Nm
If I know what the work is then I can put it into the formula Power = Work / Time
Which by me would equal 50000/ 18 = 2777.8
Could someone please tell me what the actual answer is